How a Gem Lady Treasures Collar is Made

Probably the biggest misconception about our collars is that we purchase leather dog collars and then add on the gemstones. However convenient that would be, it simply would not give us the tight quality control that we like to have on our product. I order strips of a high quality belt leather in a natural color. Two different widths are used; a five-eights inch for the xsmall & small and a one inch width for the medium, large, & xlarge.

For the collar, I take the leather strips and first cut them to the length I need. I then bevel the edges, both top and bottom. The reason is that it is more comfortable for the dog plus it is a nice finishing edge detail. Holes are then punched into the leather for the buckle to use and for assembling the collar. There is also a wrap around piece of leather that needs to be cut, beveled, and holes punched. This wrap around piece is how the buckle is attached to the collar. At this point if the leather is to be dyed black, that is done all by hand. Even when wearing gloves my hands always have a significant amount of black dye on them afterwards! Some comes off with major scrubbing and polish remover, but it usually takes several days for my hands to be back to normal! After dying and drying for 24 hours, the leather is then buffed by hand and a sealant is put on. This is then allowed to dry for at least 12 hours.

Beveling Edges
Beveling Edges
Punching Holes
Punching Holes
Stamping
Stamping

 

 

 

 

When completely dry, I use a leather stamp to stamp the size of the collar onto the wrap around piece. I also stamp my makers mark “GLT” (Gem Lady Treasures) onto the tongue of the belt. Here again care is needed when using the stamps. I have a Wedium instead of a Medium as proof! Now the assembly begins with hardware that is all nickel plated solid steel. The roller buckle is placed into the middle of the wrap around piece, being careful that the side stamped with the size is to the back side. Once again I learned this the hard way! The end of the collar is placed in-between the wrap and a rivet is hammered into place. The first dee ring is placed in-between the top of the wrap and the collar piece and then another rivet is hammered into place through all three layers. The second dee ring is added and the final rivet is hammered home. At this point, what I refer to as a ‘blank’ is completed. A blank is a collar that is ready to be stoned. I try to keep a number of sizes in blanks in both the natural and black colors on hand. That way when an order comes in, and I don’t all ready have one made, all I have to do is add the customers desired stones. By doing this I can ship out the order as fast as possible so the customer does not have to wait long for their purchase.

Not that the process up to now is not fun, but it is at this point where I can see the final dog collar coming together. When I first added the gemstones to the collars, I did a ton of measuring, converting inches (collar width) to millimeters (bead size) and back. Making sure all of my math was correct I used a quilting ruler to mark where I needed to place my needle punches. The major lesson I learned here was that despite using calibrated stones, no matter how many times I measured, how accurately I measured, and how accurately I converted my numbers, the layout was always off in some manner. I finally learned to use the actual stones themselves when measuring. By laying them out in the pattern I desired, I was able to place my needle punches in accurately. This is such a crucial part because once a punch is made, it is there forever. A needle will not go through the leather without a hole made for it. The needle punch is much smaller than a hole punch, only large enough for a needle and thread to go through the leather. If a mistake is made at this point, it is a costly mistake. After all, you have the investment of the materials and labor into a piece that is no longer useable. I have a few of these ‘very exceptional’ collars – (NOT) hanging in a special location in my workroom. I keep thinking that at some point in the future I will be able to figure out a way to use them!

Needle Punches
Needle Punches
Stoning in Progress
Stoning in Progress

 

 

 

 

We currently have two Collections for our collars. The In The Ruff Collection uses Crazy Lace Agate, Dalmatian Jasper, Labradorite, Sodalite, and Unakite. The Haute Dog Collection uses Amethyst, Apatite, Aquamarine, Carnelian, Moonstone, Rose Quarts, and Ruby Zoisite. Each of the two collections has its own design. In The Ruff has the oval gemstones laying horizontal whereas the Haute Dog Collection has the oval gemstones laying vertical. I decided on this to help separate the two collections and give my customers options. Whichever design I am using, the process is basically the same. For the Haute Dog Collection, I do a backstitch on the back of the collar and add a drop of adhesive to secure the backstitch. Then I pull the needle and thread through the needle hole, place in a knot (much like you would see on a pearl necklace), add a natural gemstone bead, place another knot and then down the next needle hole. I do not tie off after each bead is placed in because then the back of the collar would look messy with starts and stops of the thread and dots of adhesive. For the In The Ruff Collection, after securing the thread on the back, I come up through the needle punch hole, add a natural gemstone bead and then go back down the next hole. I come up again in the next hole and then place a knot. The natural gemstone bead is then added and the process is continued. In this layout, the knots are placed in-between each bead. Another thing that I should mention is that when stitching on the natural gemstone beads, the tension in the thread is very important! The thread needs to be as tight as possible so that the gemstones are on the collar as tightly as possible. This ensures that the gemstones won’t get caught on anything and accidently pulled off. After a quality control check our unique, handmade leather and natural gemstone dog collar is complete.

As you can clearly see, our Gem Lady Treasures Dog Collars are labor intensive and created with lots of love, and yes, blood, sweat, laughes and tears. Depending on which gemstones are used, they all have their own personalities. I sincerely hope that there is one in either of the collections that will suit you and your Fur Baby. If not, let us know so we can find the perfect gemstone just for you!!!

Author: gemladytreasures

Please let me introduce myself, my name is Karen M. Smith and here is a little bit about me. I have always been a lover of dogs. As a matter of fact, my dogs are known as my Fur Babies. I was in the fine jewelry industry where I fostered my love of colored gemstones. I cannot even begin to tell you how excited I am to now be able to combine my two favorite loves!

Leave a Reply

Your email address will not be published. Required fields are marked *